| Overall Rating: |
|
1
out of 5
|
Sight Rite Laser Boresighter,
November 16, 2009
By beene642
from Soddy Daisy, Tn
|
"No good for 7mm mag! I Bought this laser Boresighter with the intensions of saving some ammo and time sighting in a new rifle. The O-ring design is not a bad idea, but the the O-rings aren't sized correctly for 7mm mag. The O-rings are shown to fit both 7mm and .270, giving too much play between the muzzle and boresighter. Also, the directions say to adjust the laser itself if it is off center... doesn't that defeat the whole purpose if you have to zero the laser before you zero your scope/rifle?!?!"
|
|
Would you recommend this product to a friend?
No
|
|
Review 2 for Sight-Rite® Laser Boresighter
| Overall Rating: |
|
1
out of 5
|
junk,
November 12, 2009
By bshooter233
from Mississippi
|
"I usually do not post reviews especially bad ones...
but I had to rate this thing as absolute junk...
it was so hard to get in the barrel that it destroys the O rings...
I would be ok with that if they would atleast sent a half dozen or so replacement o rings.. I mean the product is junk and all they would have had to done to make it better was to spend another 30 cents or so in production and include more o rings!"
|
|
Would you recommend this product to a friend?
No
|
|
Review 3 for Sight-Rite® Laser Boresighter
| Overall Rating: |
|
4
out of 5
|
flatrater,
August 10, 2009
By flatrater
from lake havasu city,az
|
"the o rings for the 177 oellett gun came apart inside and also for the 22 rifle.if you could replace the o rings I would rate the bore sighter as a 4 star,it worked great on the 06s"
|
|
Would you recommend this product to a friend?
Yes
|
|
Review 4 for Sight-Rite® Laser Boresighter
| Overall Rating: |
|
1
out of 5
|
Cheap,
April 26, 2009
By lake27
|
"Main shaft that inserts into gun is made of plastic and any mishandling upon insertion or extraction permanently bends the stem that connects to main unit making the unit inaccurate.
O rings that come witht he unit are easily damaged beyond reuse."
|
|
Would you recommend this product to a friend?
No
|
|
Review 5 for Sight-Rite® Laser Boresighter
| Overall Rating: |
|
5
out of 5
|
good,
April 20, 2009
By farmdude
from south dakota
|
"good"
|
|
Would you recommend this product to a friend?
Yes
|
|
Review 6 for Sight-Rite® Laser Boresighter
| Overall Rating: |
|
5
out of 5
|
Sight Rite Laser Boresighter,
March 31, 2009
By Dave73InSC
from West Columbia, SC
|
"It is very easy to use. I used it to align my scope and a neighbor's scope on our .177 cal pellet rifles. After aligning our scopes, we did some wet firing. The shot groups were dead on, all within a 3 inch grouping."
|
|
Would you recommend this product to a friend?
Yes
|
|
Review 7 for Sight-Rite® Laser Boresighter
| Overall Rating: |
|
2
out of 5
|
Less than impressed,
February 23, 2009
By kpadawe
from Oklahoma
|
"I purchased this to boresight my new 17 HMR. it was a tight fit, no problem but it uses o-rings and one of them broke on removal. so the thing is useless to me. I looked for a o-ring kit on Cabelas but did not find one. I am not buying another fiasco that uses o-rings to get the fit.
Oh, the instructions were no help.
would not recommend."
|
|
Would you recommend this product to a friend?
No
|
|
Review 8 for Sight-Rite® Laser Boresighter
| Overall Rating: |
|
5
out of 5
|
sighting 17hmr,
January 9, 2009
By Gasfast
from Gulf Coast Texas
|
"The sight-right worked just like you specified in the instructions. The bull barrel 17hmr sighted in four holes in the center ring of target."
|
|
Would you recommend this product to a friend?
Yes
|
|
Review 9 for Sight-Rite® Laser Boresighter
| Overall Rating: |
|
1
out of 5
|
Dont wast your money,
December 27, 2008
By afoolanndhismoneyparted
|
"After reading what little instructions that came with this bore sighter I sighted in my rifle with it. The when I got to the range I found that I wasted my time and money on this product. I had to go back to the old tryed and true method of taking the bolt out and sighting it by looking through the barel. The bore sighter didnt even get me close to being on the paper."
|
|
Would you recommend this product to a friend?
No
|
|
Review 10 for Sight-Rite® Laser Boresighter
| Overall Rating: |
|
4
out of 5
|
Site-Rite,
November 20, 2008
By BRaz
from Groveton, TX
|
"As my family has grown, so has the expense every year involved with sighting in everyone's firearm, especially since the price of premium ammo stretching to around $50.00 a box. The product did everything it was advertised to do and I figure it paid for itself about three times over between myself, my wife, and four kids sighting in."
|
|
Would you recommend this product to a friend?
Yes
|
|
Review 11 for Sight-Rite® Laser Boresighter
| Overall Rating: |
|
3
out of 5
|
Sight-Rite,
October 22, 2008
By Alpo
from Washington state
|
"Pretty easy to use. Still need to tune the rifle in at the range, but it gets you on the paper. Don't lose the little washers though."
|
|
Would you recommend this product to a friend?
Yes
|
|
Review 12 for Sight-Rite® Laser Boresighter
| Overall Rating: |
|
4
out of 5
|
Site-Rite Laser Boresighter,
October 10, 2008
By SouthPlainsTexan
|
"The laser sighter seems to work quite well, and I really liked that it will work on more than one caliber. So far, am quite satisfied with it."
|
|
Would you recommend this product to a friend?
Yes
|
|
Review 13 for Sight-Rite® Laser Boresighter
| Overall Rating: |
|
5
out of 5
|
does what it's supposed to,
September 1, 2008
By burritobandito
from Nor Cal, CA
|
"it took me a few minutes to figure out how to get it set up, but it worked great."
|
|
Would you recommend this product to a friend?
Yes
|
|
Review 14 for Sight-Rite® Laser Boresighter
| Overall Rating: |
|
3
out of 5
|
Sight-Rite® Laser Boresighter,
June 23, 2008
By corbeau
from UK.,east coast.
|
"Not bad,rather fiddly and not enough 0 rings. On/off switch did not work until I adjusted it. Used on .177 and .22 air rifles with reasonable effect.Does the job."
|
|
Would you recommend this product to a friend?
Yes
|
|
Review 15 for Sight-Rite® Laser Boresighter
| Overall Rating: |
|
4
out of 5
|
First shot MOA,
May 5, 2008
By 556SHOOTER
from Birmingham, Al
|
"I used this product to sight in my new SIG-556, on my HYSKORE gunsmith bench, at home, following the included instructions. My first shots at the range were MOA quality at 100yds. I did have to remove the FLASH SUPRESSOR in order to install the boresighter into the barrel. Results were worth the extra step."
|
|
Would you recommend this product to a friend?
Yes
|
|
Review 16 for Sight-Rite® Laser Boresighter
| Overall Rating: |
|
1
out of 5
|
bad out of the box,
April 14, 2008
By sandiegoshooter
from san diego ca
|
"The first time I used the bore sighter in my .17 cal it broke. Thier are 2 washers on the shaft you put down the bore to take up the slack between the shaft and the bore. One washer broke the other came off the guide holding it in place. I did not try the other shaft that screws on lazer for other calibers yet. Cabelas is making good on it and sending me a new one as soon as I send back the old one. Hoping it was only a bad one in the batch.."
|
|
Would you recommend this product to a friend?
No
|
|
Review 17 for Sight-Rite® Laser Boresighter
| Overall Rating: |
|
2
out of 5
|
mmmm,
April 14, 2008
By rthrhunt
from John Day, Oregon
|
"The O-ring system for fitment to caliber is to inconsistent. I used this bore sighter on a new .223 and each time it was removed and re-installed the the laser was in a totally different area of the sight picture. Not even close. Will try it on my other rifles to see if it is just the o-rings too loose for the .223 but not happy so far."
|
|
Would you recommend this product to a friend?
No
|
|
Review 18 for Sight-Rite® Laser Boresighter
| Overall Rating: |
|
4
out of 5
|
rm53,
April 13, 2008
By rm53
from Cape Girardeau, Mo
|
"Works okay for the money."
|
|
Would you recommend this product to a friend?
Yes
|
|
Review 19 for Sight-Rite® Laser Boresighter
| Overall Rating: |
|
3
out of 5
|
Close but no cigar,
April 1, 2008
By MachineGuy
from West Bend Wi.
|
"I actualy purchased this item to line up bar feeds on our CNC lathes. Checked it by rolling the assembled unit in a precision v-block and made a mark on a wall at a distance of only three feet. The red dot ran out 1/2" at this short distance. I only need accuracy to 14 feet but, you can imagine how far off it would be at a 50-100 yards.
The point isn't really round. More like a short line than a dot. Nice and bright though.
In fairness you can adjust the beam with three set screws but the unit should be set better than what I got in three feet.
I'd recommend it to a friend but, knowing I'd probably need to adjust it for them.
Comes with a cloth bag to keep all the bits in.
Qualty 4 stars
Accuracy 1 Star"
|
|
Would you recommend this product to a friend?
Yes
|
|
Review 20 for Sight-Rite® Laser Boresighter
| Overall Rating: |
|
4
out of 5
|
speed,
March 31, 2008
By veteranone
from nicholasville,ky.
|
"for the money, can't beat it! fast way to sight in. just carry it around with you when you hunt. thanks"
|
|
Would you recommend this product to a friend?
Yes
|
|
